The Foundation of Plumbing Knowledge When Installing a Bathtub

Schedule Services


Listed here below you can find more high-quality insight when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately hard job. If the old bathtub is easily easily accessible, the project can move speedily; if you need to open up a wall to remove the old tub and place the brand-new bath tub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need an assistant to move out the old bathtub and set in the new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed project, it is better to take into consideration utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This post will certainly help you install a brand-new bathtub in your bathroom if you have actually currently gotten a new bathtub and also do not require to transform the setup of your previous supply of water pipelines.
Your tools as well as material checklist ought to consist of the following:


  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  •  

Getting ready for the Installation


Firstly, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to avoid pressure on the bathtub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final position.



Removing Old Touches


If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.



Mounting the Tub


Using both wood boards under its feet, place the tub in the called for setting. The wood boards are helpful in uniformly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub until the level reads level.
To install faucets, fit the bottom of the furthest versatile tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and also new pipework for leakages and tighten them if required. Load the tub and additionally inspect the overflow outlet and also the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub should wait up until the tub has actually been used at least once as this will certainly resolve it right into its last setting.



Suitable New Touches


If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The former type ought to be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.



Tiling Around the Tub


In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack an inflexible seal, causing the water to penetrate the wall surface in between the bath and the tiling, bring about difficulties with dampness as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes and cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to allow for the motion experienced when the tub remains in usage. The sealant can break rather early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant adhesive as well as grout.


Bathtub Installation


How Important Is A Bathtub To Your Home?


High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


Install Piping Before Tub


You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


Position the Tub


Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


Assemble Drain Connections


Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


Place a Pipe For the Shower Head


First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


Attaching Hot and Cold Water Lines


Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


Install the Spout


Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


Check For Leaks


Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


estore the Bathroom Wall


Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


How to Install a Bathtub


I was shown that editorial about Installing A Bathtub through a good friend on another website. You should set aside a second to promote this article if you liked it. Thank-you for your time invested reading it.


Avoid further plumbing damage; call.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “The Foundation of Plumbing Knowledge When Installing a Bathtub”

Leave a Reply

Gravatar